[转]自制垂降手套(OSW)

colorwolf · 发表于 2005-11-16 00:13

1.TWO ROWS OF STITCHING
  2行的缝合
  TRIM CLOSE AFTER STITCHING
  缝合后把线剪掉
  FAKE SUEDE
  仿制皮革
  GREAM LEATHER
  ??(应该是平滑的皮革)
  GOOD SIDE DOWN
  好看的一面向下

2.SEW THE TWO BLANKS TOGATHER GOOD SIDES TOGATHER
  把2个外皮(好看的一面)缝在一起
  MARK OUT PATTERN
  用样本做记号

3.NOTE:ONE STICH BETWEEN EACH FINGER AND EACH FINGER IS THREE STICHES WIDE
  注意:手指间的宽度是3倍的车缝针线
  START SEWING/FINISH SEWING
  开始/结束车缝
  DOUBLE STITCHED
  缝合2次

4.GLOVE TRIMED WITH SHARP XACTO BLADE
  手套用裁缝剪刀修剪
  2MM BRASS ROD IN THE PIN CHUCK
  在手钻里放2MM的铜枝
  4MM STYRENE EVERGREEN TUBE WITH ROUNDED EDGE
  4MM EVERGREEN牌的改造树脂圆柱

5.4MM TUBE PUSHED INTO GLOVE FINGER FROM INSIDE ALL THE WAY TO THE END
  把4MM的圆柱从里面推到手指头
  2MM BRASS ROD USED TO PRESS FINGER INSIDE OUT
  2MM 的铜枝用来把外面的"手指头"压平

This shot shows that I have to support the finger and let the tube be pushed out by the brass rod. Once you do it once you'll see it's dead easy to turn the fingers inside out. All done inside of a minute.
这张照片显示我必须用树脂圆柱支撑手指头然后向外推出去靠铜枝压平。如果你动手你会发现这步骤很简单。全部在1分钟内搞定

成品

翻译得不好请多多包含有请高手指正

ZIP · 发表于 2005-12-6 17:05

以下是引用kingship在2005-12-6 16:59:00的发言：
怎么都是xxxxx

嘿嘿面条兄没在OSW上注册吧所以看不到了

我重新上传下

我要说一句收起回复

ZIP · 发表于 2005-12-6 17:09

<img src="attachments/dvbbs/20051261755068654.jpg" border="0" onclick="zoom(this)" onload="if(this.width>document.body.clientWidth*0.5) {this.resized=true;this.width=document.body.clientWidth*0.5;this.style.cursor='pointer';} else {this.onclick=null}" alt="" />
1.TWO ROWS OF STITCHING
  2行的缝合
  TRIM CLOSE AFTER STITCHING
  缝合后把线剪掉
  FAKE SUEDE
  仿制皮革
  GREAM LEATHER
  ??(应该是平滑的皮革)
  GOOD SIDE DOWN
  好看的一面向下
<img src="attachments/dvbbs/2005126176028625.jpg" border="0" onclick="zoom(this)" onload="if(this.width>document.body.clientWidth*0.5) {this.resized=true;this.width=document.body.clientWidth*0.5;this.style.cursor='pointer';} else {this.onclick=null}" alt="" />
2.SEW THE TWO BLANKS TOGATHER GOOD SIDES TOGATHER
  把2个外皮(好看的一面)缝在一起
  MARK OUT PATTERN
  用样本做记号

<img src="attachments/dvbbs/20051261761230147.jpg" border="0" onclick="zoom(this)" onload="if(this.width>document.body.clientWidth*0.5) {this.resized=true;this.width=document.body.clientWidth*0.5;this.style.cursor='pointer';} else {this.onclick=null}" alt="" />
3.NOTE:ONE STICH BETWEEN EACH FINGER AND EACH FINGER IS THREE STICHES WIDE
  注意:手指间的宽度是3倍的车缝针线
  START SEWING/FINISH SEWING
  开始/结束车缝
  DOUBLE STITCHED
  缝合2次

<img src="attachments/dvbbs/20051261762127845.jpg" border="0" onclick="zoom(this)" onload="if(this.width>document.body.clientWidth*0.5) {this.resized=true;this.width=document.body.clientWidth*0.5;this.style.cursor='pointer';} else {this.onclick=null}" alt="" />

4.GLOVE TRIMED WITH SHARP XACTO BLADE
  手套用裁缝剪刀修剪
  2MM BRASS ROD IN THE PIN CHUCK
  在手钻里放2MM的铜枝
  4MM STYRENE EVERGREEN TUBE WITH ROUNDED EDGE
  4MM EVERGREEN牌的改造树脂圆柱

<img src="attachments/dvbbs/20051261763054641.jpg" border="0" onclick="zoom(this)" onload="if(this.width>document.body.clientWidth*0.5) {this.resized=true;this.width=document.body.clientWidth*0.5;this.style.cursor='pointer';} else {this.onclick=null}" alt="" />
5.4MM TUBE PUSHED INTO GLOVE FINGER FROM INSIDE ALL THE WAY TO THE END
  把4MM的圆柱从里面推到手指头
  2MM BRASS ROD USED TO PRESS FINGER INSIDE OUT
  2MM 的铜枝用来把外面的"手指头"压平

<img src="attachments/dvbbs/20051261763936305.jpg" border="0" onclick="zoom(this)" onload="if(this.width>document.body.clientWidth*0.5) {this.resized=true;this.width=document.body.clientWidth*0.5;this.style.cursor='pointer';} else {this.onclick=null}" alt="" />
This shot shows that I have to support the finger and let the tube be pushed out by the brass rod. Once you do it once you'll see it's dead easy to turn the fingers inside out. All done inside of a minute.
这张照片显示我必须用树脂圆柱支撑手指头然后向外推出去靠铜枝压平。如果你动手你会发现这步骤很简单。全部在1分钟内搞定

我要说一句收起回复

ZIP · 发表于 2005-12-6 17:09

<img src="attachments/dvbbs/20051261764930191.jpg" border="0" onclick="zoom(this)" onload="if(this.width>document.body.clientWidth*0.5) {this.resized=true;this.width=document.body.clientWidth*0.5;this.style.cursor='pointer';} else {this.onclick=null}" alt="" />

<img src="attachments/dvbbs/2005126177131580.jpg" border="0" onclick="zoom(this)" onload="if(this.width>document.body.clientWidth*0.5) {this.resized=true;this.width=document.body.clientWidth*0.5;this.style.cursor='pointer';} else {this.onclick=null}" alt="" />

<img src="attachments/dvbbs/2005126177978701.jpg" border="0" onclick="zoom(this)" onload="if(this.width>document.body.clientWidth*0.5) {this.resized=true;this.width=document.body.clientWidth*0.5;this.style.cursor='pointer';} else {this.onclick=null}" alt="" />

再次感谢“色狼”兄：）

我要说一句收起回复

kingship · 发表于 2005-12-6 16:59

怎么都是xxxxx

我要说一句收起回复

EW-4 · 发表于 2005-12-6 18:19

我没注册，也看到了啊

我要说一句收起回复

ZIP · 发表于 2005-12-7 00:16

以下是引用EW-4在2005-12-6 18:19:00的发言：
我没注册，也看到了啊

那或许是网络地域问题了吧

我要说一句收起回复

zhu · 发表于 2005-12-12 19:02

好招!

我要说一句收起回复

taurus2004 · 发表于 2005-12-12 20:30

好鐵

我要说一句收起回复

liufeimx · 发表于 2006-1-23 17:04

好

我要说一句收起回复

帐号		自动登录	找回密码
密码			注册